A cheap and charming color laser printer A cheap and charming color laser printer by Dan Ackerman. The HP Tango X writes the book on bookshelf printers. Lift the printer and lower it onto the two stacked paper feeders, aligning the pegs on the upper paper feeder with the holes on the bottom of the printer. Page 95 User Guide Paper Jams Squeeze the tabs on the top rear of the printer and pull the rear cover toward you to open it. Tablets by David Carnoy 7 days ago.
|Date Added:||8 December 2010|
|File Size:||67.90 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
Make sure the tabs are toward the right side of the printer. Use the following procedure to enter the paper menu: Push the paper tray all the way into the printer, making sure the tray is properly seated. If looking through the Genicom microLaser user manual directly on this website is not convenient for you, there are two possible solutions:. Paper Jam Locations and Error Codes.
Broken components or scraps of paper lodged inside the feeder may be brushing against mov- ing parts and causing the noise. Use the following procedure to enter the Functions Menu: If the AC wall outlet is broken, allowing the power cord to easily fall out, replace the mocrolaser. Position the new BTR roller so the gear is at the right end of the roller.
Cleaning The Printer User Guide Cleaning the Printer Insert the pegs on the toner cartridge into the channels inside the printer, and push the toner cartridge into the printer. Front Cover Provides access to the interior of the printer. Remove the toner cartridge from the inside of the printer.
Most duplexer error codes indicate routine status conditions such as a paper tray running out of paper or a paper jam in a specific area of the duplexer.
Maintaining The Sheet Feeder User Guide Maintaining the Sheet Feeder Remove the paper trays and inspect the inside of the feeder for jammed paper or obviously broken components. The duplexer makes unusual noises or makes more noise mcirolaser usual either while idle or while printing.
If you are planning to use large size envelopes, pull out the extension at the end of the paper tray. To start viewing the user manual Genicom microLaser on full screen, use the button Fullscreen.
Electrical noise may be transmitted through the AC line. Squeeze the lock clip on the inside right of the rear cover, and slide it toward you.
Genicom microLaser user manual – – Solve your problem
Correcting Miscellaneous Duplexer Problems Some duplexer problems may not cause an error message and may not interfere with the operation of the printer. Don’t have an account? Page of Go. Correcting Miscellaneous Offset Catch Tray Problems Some offset catch tray problems may not cause an error message and may not interfere with the operation of the printer.
Pull the tray all the way out and lift the paper stop. Push the paper tray completely into the printer, making sure the tray is properly seated.
If the problem reoccurs, Turn the printer on by pressing [ I ] on the power switch on the left front of the printer. Please read this manual in its entirety and keep it at hand for later reference.
About The Duplexer User Guide About the Duplexer About this Chapter This chapter provides all of the information necessary to install, use, and maintain the duplexer.
Push the envelope feeder all the way into the printer until it stops, making sure it is seated firmly inside the printer. Inoperative Printer User Guide Installation Problems Inoperative Printer If you have problems turning on the printer, check the possible causes listed in the table below.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. You do not have to print the entire manual Genicom microLaser but the selected pages only.
Genicom microLaser 210 user manual
Use the following procedure to clear a duplex paper jam: Close the front cover, pressing on the center of the front cover until it closes securely. Cleaning the Exterior of the Envelope Feeder Through normal use the exterior of the envelope feeder may become 2100 or stained with toner. The offset catch tray makes unusual noises or makes more noise than usual either while idle or while printing.